Calculations are an important part of planning around a construction project. From concept to completion of the project calculation is a tool to try to predict the actual cost. During the production stage in particular, deviations occur which makes the actual cost different from the calculations.This thesis is done in collaboration with JM Residential Stockholm. The study includes a cost follow-up in which a comparison was made between the calculated Production cost and actual cost for the five projects. The aim of the study was to observe the most common reasons that a project deviates from the calculated Production cost and then summing these causes in a number of categories.

The cost of construction projects have increased during the past few years. Different actors in the construction industry work together to advocate various measures to mitigate these cost increases. One of these measures is to try to improve the efficiency in the phase of production. By striving for a kind of standardization with a constant quest for improvement, the productivity can increase while the costs of production fall.For this thesis has a case study been conducted at the construction company JM AB which is seeking this. They call the approach structured production and have implemented various measures to achieve a more productive output.Based on information from reconciliations, the cost and the spent hours of craftsmen have been analyzed at the company where the case study took place.

Göteborg Energi has a surplus of district heating during spring, summer and fall. The heat surplus is due to a constant production of waste heat from oil refineries and heat from waste incineration over the year. It would be desirable to increase the demand for heat and the uptime for the newly built combined heat and power generation plant, Rya Kraftvärmeverk. One alternative could be to integrate Rya Kraftvärmeverk with a pellet production facility. By producing heat, electricity and pellet in a joint process the energy use can be decreased.

Ocean Thermal Energy Conversion, OTEC, is a sustainable energy conversion technology that is not yet commercialized. OTEC is a technology that utilizes the temperature difference in oceans between the warm surface water and the cold water at 1 000 m depth to run a Rankine Cycle. This technology can produce electricity and provide synergies like fresh water, air conditioning and aquaculture. A simulation program for three alternative OTEC systems has been created in order to decide which OTEC system is most profitable; closed, open or hybrid system. In this simulation a Production cost analysis is performed in order to investigate and decide which one of the three systems that has the lowest Production cost. The Production cost analysis also analyzes if the profitability is affected by the size of the facility. After these analyzes, the most profitable of the three different OTEC-systems is expanded by an installation of solar collectors in order to see if the thermal efficiency is improved. The result shows that the most profitable system varies with the size of the facility.

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS Production costs is possible. .

AbstractIt is important to choose which spare parts to keep in stock. With the right spareparts in stock the costs for inventory and production loss will decrease. Cavalieri et al. (2008) highlights that the balance between inventory cost and production loss is underestimated.  It affects the company and must be considered before decision on purchase.The problem with spare engines is that they are all more or less critical for the production. That can be a reason for why no previous research targeting engines and classification of with engine should be kept in stock has been found.

Lean Production is used by many manufacturing companies. Companies in process industries do not use Lean Production to the same extent today. This is part of the report's issue to explore how Lean Production can be applied to a company in the process industries.The investigated company is a processing company that manufactures various types of foil. The company wishes to streamline its production and has therefore asked the authors to examine if Lean Production can offer the company improvements in their production. Lean Production value stream mapping tool has been selected to identify and analyze the current state of two of its products in production.

The purpose of this report is to survey Swedex AB?s Production costs and to gather all info into a manageable calculation tool. This was made by time and motion studies, interviews of the personnel. All factors were gathered into an Excel chart.The calculation was made according to an additional-charge-method that was considered to satisfy Swedex AB?s goal.

The Swedish production of biogas was 1,5 TWh 2011. About half of the production was used as vehicle fuels. The cost for upgrading biogas depends on the size of the biogas plant and its gas production. If the gas flow is low the cost will be high. However, further development of existing upgrading technologies or development of new ones, have good potential to decrease the upgrading cost for small scale biogas plants.

The avowed aim in this project was to see how the Swedish egg production is today. My first question was if the Swedish egg producers egg production turn a profit. I have done five after calculation at five different egg producers with different systems from case to case. The difference has been the living system, the fodder and the egg price. They made a report in Uppsala, Sweden (Hoffman & Andersson, 1996), where the look forward to a Swedish cage ban and made calculations after that coming ban. After that they lift the Swedish ban of cages and the egg producers could invest in new cages who called the decorated cage.

This study deals with the technical and economic feasibility of replacing the nuclear power plant reactor Ringhals 3 with a biofuel power plant. A technical investigation has been executed to determine which of the systems and components that could be reused and which ones would need to be replaced. The investment costs of the reconstruction have also been estimated. The cost of the electricity production has been calculated as well as the emissions of the new biofuel power plant. Based on the established rate of return, the lowest average spot price of electricity that makes the investment profitable has been calculated.

An increasing number of automotive supplier companies are investing in Central and Eastern Europe (CEE) in order to gain cost advantages. This has happened in a rapid pace since many of these countries did not have any foreign direct investments (FDI) at the turn of the century. The problem now is for how long these countries will be able to maintain the low costs. One purpose was to create a model of country advantages for automotive supplier companies when relocating further production to CEE. This dissertation was written in cooperation with the Trelleborg Group.

AbstractLean production has become one common concept within industries to make the work more effective and to meet today?s hard competition. A challenge for Chinese production is the threat from new low cost countries. It will become very difficult to succeed to produce to a lower cost than these countries; this led to that Chinese companies must develop new strategies, according to Lee and Zhou (2000). This will put China in front of new challenges and new strategies can be needed to retain their strong competitive advantages.

This thesis investigates management accounting systems in a Swedish health care environment. Through a qualitative case study of an activity-based cost accounting system that was introduced in 1994 at S:t Görans Sjukhus, a large Stockholm hospital, the following questions are addressed: What benefits can an activity-based cost accounting system offer the Swedish health care providers? What are the potential problems impeding the implementation of such a system? Main findings: an activity-based cost accounting system can improve the understanding of where costs are generated in the production processes. Comparisons between alternative production processes are improved, and the data may serve as a basis for internal pricing measures. Concerning the second question, difficulty in reconciliating the principles of economic control with the culture present in a hospital is identified as the main obstacle to a new management accounting system..

The use of fossil fuels such as coal and gas are a contributor to the global warming. The climate change is a worldwide problem with far reaching consequences that is believed to be very expensive. The United Nations has been introducing a framework convention on climate change. One component of the convention is the Kyoto protocol. The protocol is obligating the developed countries to decrease their emissions of greenhouse gases by 5.2 percent during the time period 2008-2012.